Futaba 3VCS User Manual Page 7
- Page / 112
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8
For Your Safety As Well As That Of Others
Caution
Prohibited Procedures
Mandatory Procedures
Do not touch the engine, motor, speed control or any part of
the model that will generate heat while the model is operating
or immediately after its use.
These parts may be very hot and can cause serious burns.
Turning on the power switches.
Always check the throttle trigger on the
transmitter to be sure it is at the neutral
position.
1. Turn on the transmitter power switch.
2. Turn on the receiver or speed control
power switch.
Turning off the power switches
Always be sure the engine is not
running or the motor is stopped.
1. Turn off the receiver or speed control power switch.
2. Then turn off the transmitter power switch.
If the power switches are turned off in the opposite
order the model may unexpectedly run out of control
and cause a very dangerous situation.
When making adjustments to
the model do so with the en-
gine not running or the motor
disconnected.
You may unexpectedly lose control and
create a dangerous situation.
When operating your model
always display a frequency
flag on your transmitter an-
tenna.
When adjusting the transmitter on land while preparing to run (cruise), take measures
so that the wind will not knock over the transmitter.
If the transmitter is knocked over, the throttle stick may be accidentally set to the operating position and you may
lose control.
(Fail safe function) ---H.R.S or PCM mode only
Before running (cruising), check the fail safe function.
Check Method;
Before starting the engine, check the fail safe function as follows:
1) Turn on the transmitter and receiver power switches.
2) Wait at least one minute, then turn off the transmitter power switch. (The transmitter automatically transfers the fail
safe data to the receiver every minute.)
3) Check if the fail safe function moves the servos to the preset position when reception fails.
The fail safe function is a safety feature that minimizes set damage by moving the servos to a preset position when
reception fails. However, if set to a dangerous position, it has the opposite effect. When the reverse function was used
to change the operating direction of a servo, the fail safe function must be reset.
Setting example: Throttle idle or brake position
ON
OFF
1
2
3
B/C
FP-R113F
FM
- RECEIVER (FOR U.S.A.) 1
- Table Of Contents 3
- Explanation of Symbols 5
- Operation Precautions 6
- Prohibited Procedures 7
- Prohibited Items 8
- Mandatory Procedure 9
- Other Precautions 10
- Before Using 11
- Set Contents 13
- Transmitter T3VCS 14
- RF.MODULE 15
- TRANSMITTER 15
- Digital Trim Operation 16
- Button Trim Operation 16
- Neutral Adjuster Operation 17
- Stick Lever Head Adjustment 17
- Stick Tension Adjustment 18
- Mechanical ATL Adjustment 18
- Charging the Ni-cad Battery 19
- Ni-cad Battery Replacement 19
- Mandatory Procedures 19
- RF Module 21
- Data Backup 21
- Set data backup 22
- Display switch 22
- LCD Screen Contrast 24
- Total timer 24
- Receiver 25
- Installation 26
- Instal set-Up 28
- 2. Modulation Mode Check 29
- 4. Trims Initial Set-Up 29
- 3. Throttle Mode check 29
- Steering dual rate 30
- Throttle ATL 30
- Function Map 31
- Direct Selection 32
- Functions 33
- MENU SELECT 34
- DIRECT SEL 34
- A.B.S. Function 45
- E50%の場合 47
- Setup items 53
- Preset position 53
- Setup item switching 53
- Function ON/OFF 55
- Brake return amount 55
- Delay amount 55
- Switch Setting 56
- Timer/TIMER 57
- UP TIMER 57
- DOWN TIMER 57
- LAP TIMER 58
- LAP NAVIGATE timer 59
- Lap list/LAP-LIST 64
- Program Mixing 1,2/PRG-MIX1,2 65
- 7 (Mixing mode setup) 66
- -100~0~+100 66
- Subtrim/SUB-TRIM(All channel) 70
- Fail safe function/FAIL SAFE 72
- Model Select/MDL-SEL 74
- Model Reset/MDL-RES 76
- Model Copy/MDL-COPY 77
- Model Name/MDL-NAME 78
- HRS/PCM/PPM select/MOD-MODE 87
- Level Select/LEVEL-SEL 88
- Adjuster/ADJUSTER 89
- Throttle adjustment 90
- System function/SYSTEM 91
- Direct call/DIRC-CALL 93
- Servo view/SERVO 95
- HRS ECS setup/MC-SETUP 96
- Trottle mode/THR-MODE 98
- Reference 100
- Optional Parts 101
- Case mounting screws 104
- Swing arm 104
- Ratchet plate 104
- Troubleshooting 105
- Error Displays 106
- When requesting repair 108
- Glossary 109
- Glossary (LCD Display) 110
- ORANGE LED: Orange 111
- FUTABA CORPORATION 112
Related products and manuals for Accessories communication Futaba 3VCS
(9 pages)© 2020, manymanuals.com. All rights reserved. | 0.672 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals